How to install a gas range properly?

Do you always face difficulties with your gas range? Do the gas range risks frighten you at night? Or do you go out of your blanket many times just to check if the gas is leaking or not?

Here we have bought some important key factors that you must follow to overcome the various risks related to your gas stove. The most important part when it comes to a gas range is its proper fixing or installation. If your stove is not installed properly it is likely to put you at dangerous risks sometimes. It is also preferable to call professional gas installers to get your system properly installed. But this can be an expensive affair for many. But you can always learn the procedure and save at least a hundred dollars. So, here we are providing you with a guide which will help you to install your gas range by yourself. The process is explained step-by-step.

Caution Before you start replacing your gas stove you must make sure that homeowner installation is permitted through the local codes and ordinances.

How to install a gas range?

Materials that you would probably require are – Flexibly furrowed gas pipe, wrench, yellow Teflon pipe joining tape, gas leak detector, liquid soap.

Step 1: Be careful while buying the gas stove connector/pipe

The pipe that connects the gas to the stove is the most sensitive part of the system. Any leak or hole in the pipe due to low quality may head you to huge risks. So, you must be careful while purchasing it. Go to any hardware shop to buy the best quality connector. Buying the right connector is the most important step to a safe installation. While buying the connector consider these points –

Check and make sure of its marking for a range.

Check the endings of the pipe it must contain the perfect fittings you need for your stove. Usually, the gas line will be a 1/2-in. black threaded pipe and the connection to the stove will be a male (external threads) or female (internal threads) 1/2-in. fitting. It is always better to have the inbuild fittings but in case if you cannot find connectors with end fittings then seal the endings with black tape that will safeguard your system from probable gas leaks.

Always choose a longer gas pipe as it will provide you with the room to work between the wall and the stove.

Step 2: pull out the range

Pull out the range and shut off the gas cock (it’s off when the lever is at a right angle to the pipe). The shutoff will either be located behind the range or in the basement just below. If you don’t have a shutoff, this is the best time to add one for your safety.

Step 3: Wrap the pipe threads

Wrap yellow Teflon pipe-joint tape twice around the threads clockwise. The 1/2-in. x 3/4-in. coupling accommodates the 3/4-in. end connector fitting, since connectors with 1/2-in. end fittings at both ends are not always readily available.

Step 4: Attach the connector to the gas line

Remove the end connector fitting, wrap the unbeveled end with Teflon tape, and screw it to the gas line. Safety tip: ALWAYS use both of the end fittings and NEVER screw the connector nuts to a black gas fitting or pipe or you will be guaranteed a leak. Also, be careful not to kink or force the connector into sharp bends.

Step 5: Use a street elbow

Screw a 1/2-in. x 1/2-in. street elbow into the range gas port. Then screw the connector’s other end fitting into the street elbow. Use Teflon tape on each fitting, and be careful not to overtighten.

Step 6: Tighten the nuts

Tighten the connector nuts to the two end connector fittings, making sure to hold the tube straight against the fitting. Safety tip: Do NOT use Teflon tape on these threads as it can interfere with the seal.

Step 7: Check for leaks

IMPORTANT: Always check your work for leaks. Turn on the gas cock (vertical position) and light the range burners for about a minute to get the air out of the gas line. Then spray all the joints with a gas leak detector (sold at home centers). You can also use warm, soapy water. If there are any bubbles around a joint, this indicates a leak. For added safety, you can call your local gas company to check your work.

Step 8: Move the new stove in place

If there are no leaks detected, push your new stove in place and make sure everything is level. When you’re all set, it’s time to get cooking!

Safety is the key! While installing any gas range you must consider the safety of the system and all risk factors must be avoided. The quality of the products must be never ignored. As a little ignorance may cause a huge disaster. Check if homeowner installation is permitted on your product or not. Always call experts in case of casualties.

For the best performance from stovetop to ovens, these are the best gas ranges to buy in 2020, according to testing:

Best Overall Gas Range: LSG4511ST Slide-In Gas Smart Wi-Fi Range

Best Value Gas Range: Samsung NX58R6631ST Freestanding Gas Range

Best Powerful Gas Range: Miele HR1124G Freestanding Gas Range

Best Customizable Gas Range: BlueStar RNB304BV2 RNB Series Range

Best No-Frills Gas Range: Whirlpool WFG505M0BS Freestanding Gas Range

Best Dual Oven Gas Range: SMEG CPF48UGMYW Portofino Pro-Style Dual Fuel Range

Easiest-to-Use Gas Range: KitchenAid KSGB900ESS Slide-In Gas Range

Best Features Gas Range: Frigidaire Gallery FGGH3047VF Gas Range with Air Fry

Easiest-to-Clean Gas Range: GE Profile PGS930SELSS Smart Slide-In Front-Control Gas Range

A new gas range is a serious investment — it’s also the heart of your kitchen.

Leave a Reply